Unicyclist Community

Go Back   Unicyclist Community > Unicycling Discussion > General Unicycling Discussions

Reply
 
Thread Tools Search this Thread Rate Thread Display Modes
Old 2015-11-06, 02:15 AM   #1
StevePunkerton
Unicyclist
 
StevePunkerton's Avatar
 
Join Date: Nov 2015
Location: Merrill, Michigan
Age: 26
Posts: 3
Unhappy Am I too heavy for this Unicycle?

Hiya all,

I've been looking to get a unicycle for a while now and today I found one at a significant discount so I bought it on an impulse without much research only to realize it says it has weight limit of 143 pounds. I'm clocking in somewhere around 190-200 so is this one a lost cause? If so could you recommend a Unicycle that would fit my weight please?

This is the amazon listing for the Unicycle if that helps:


Thank you for taking the time to read this and respond,
Steve
StevePunkerton is offline   Reply With Quote
Old 2015-11-06, 02:43 AM   #2
saskatchewanian
ERIC P
 
saskatchewanian's Avatar
 
Join Date: Jan 2007
Location: La Ronge, Saskatchewan, Canada
Age: 34
Posts: 6,471
I would just ride what you got for now. it should be OK if you ride smoothly, try not to hop, jump or ride off ledges very often and you should be fine.

If you wreck the cranks replace them with aluminum ones.

If the seatpost is thin you can trim the bottom curled in section and pound a dowel up the middle.

Also check the wheel tension. Even a cheep wheel will last a good long time if properly maintained.
__________________
My friends, love is better than anger. Hope is better than fear. Optimism is better than despair. So let us be loving, hopeful and optimistic. And we’ll change the world. - Jack Layton
saskatchewanian is online now   Reply With Quote
Old 2015-11-06, 02:46 AM   #3
johnfoss
North Shore ridin'
 
johnfoss's Avatar
 
Join Date: Apr 2002
Location: El Dorado Hills, CA
Age: 57
Posts: 17,128
If you're learning to ride, it should be just fine. If the seat goes high enough. Don't use it for Trials.
__________________
John Foss
www.unicycling.com

"Who is going to argue with a mom who can ride a unicycle?" -- Forums member "HiMo"
johnfoss is offline   Reply With Quote
Old 2015-11-06, 02:59 AM   #4
StevePunkerton
Unicyclist
 
StevePunkerton's Avatar
 
Join Date: Nov 2015
Location: Merrill, Michigan
Age: 26
Posts: 3
Great! Thanks for the quick response saskatchewanian and John! I'll be sure to keep in mind all that you said once I get a moment to try it out. I don't plan of trying to do any tricks in the foreseeable future, just riding around town until I get a good grasp of it.

Thanks again,
Steve
StevePunkerton is offline   Reply With Quote
Old 2015-11-07, 06:56 AM   #5
kayakzz
Unicyclist
 
Join Date: Jun 2014
Location: Williamsburg, VA
Age: 56
Posts: 95
If you want to go with a cheap Chinese uni, that will work. It is how I started and it makes sense until you figure out if you are interested in the sport. I would recommend a 24" in wheel although either will work.
kayakzz is offline   Reply With Quote
Old 2015-11-08, 12:06 PM   #6
Reeny
Unicyclist
 
Join Date: Jun 2015
Location: UK, Northumberland
Posts: 195
Agreed - the 24 would have been better for you once you get your balance and get rolling.
Saying that, I have the 20" version with the PowerCircle aluminium double skinned rim and it is fine for me at 180lbs.

I have needed to buy a few parts from UDC:
Seat and post - much stiffer / less flex than the Chinese version
Cranks - 114's to change the gearing as I get better.
Spoke key - the wheel was creaking badly, a spoke key fixed it.


The seat is a must do recommeded change - My skills improved as soon as the UDC saddle was fitted.
You need a £5 ($8) seat post to fit the new saddle.
The cranks can come later, or invest in a 24" from Ebay, or UDC
http://www.ebay.co.uk/itm/20-24-Unic...Yy3TCXslv9mRQA

My first cycle is the black 20" / eventually I moved up to the 24" Orange Club.
The 20" is obviously too small - the 24" fits me better

Last edited by Reeny; 2015-11-08 at 12:16 PM. Reason: Photo added
Reeny is offline   Reply With Quote
Old 2015-11-09, 08:25 AM   #7
Reeny
Unicyclist
 
Join Date: Jun 2015
Location: UK, Northumberland
Posts: 195
22.2mm seat post

Note, if/when you do the seat upgrade, you need the 400mm long, 22mm diameter seat post, with a decent saddle.
You will know how much longer the post needs to be once the cycle arrives.
UDC UK is a lot cheaper than the USA shop for the same parts.
$30 saddle (or £15 / $24) http://www.unicycle.com/unicycle-har...ddle-club.html
$18 700mm long, 22.2mm seat post (or £6/ $10) http://www.unicycle.com/unicycle-har...post-3563.html

I would look here for the parts, then check the additional cost for overseas postage.
You have $14 to play with.
UDC Saddle http://www.unicycle.uk.com/club-unic...dle-black.html
400mm Post http://www.unicycle.uk.com/unicycle-...post-22-2.html
Reeny is offline   Reply With Quote
Old 2015-11-09, 10:38 AM   #8
Mononovize
Unicyclist
 
Join Date: Oct 2014
Posts: 109
You may also need to pay customs...
Mononovize is offline   Reply With Quote
Old 2015-11-13, 06:21 PM   #9
StevePunkerton
Unicyclist
 
StevePunkerton's Avatar
 
Join Date: Nov 2015
Location: Merrill, Michigan
Age: 26
Posts: 3
Thanks to everyone for the helpful comments! I finally got it put together today and can't wait to start learning, I'll be keeping everything you've all said in mind!
__________________
I'm too unique to pay rent!
StevePunkerton is offline   Reply With Quote
Old 2015-11-15, 01:22 PM   #10
Reeny
Unicyclist
 
Join Date: Jun 2015
Location: UK, Northumberland
Posts: 195
I was doing one improvement per day - where a day = 1-hour max, in small 5-minute sessions
Day-1 = able to sit on the thing holding onto a hand rail
Day-2 = able to do 1/2 revolution holding onto a hand rail
Day-3 = able to do 1/2 revolution without holding onto a hand rail
Day-4 = able to do 1 full revolution without holding onto a hand rail
Day-5 = able to do 1 and a 1/2 revolutions
Day-5 = able to do 2 full revolutions etc

The more you practice - the quicker you will learn.
I am in no hurry, and taking my time.

The 20" is useful to practice new tricks on.
I will be keeping mine as a lightweight "grab and go" unicycle.
Reeny is offline   Reply With Quote
Reply

Tags
heavy, unicycle


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
This would be amazing for Unicycle filming one4all General Unicycling Discussions 26 2014-07-20 03:54 PM
Am I too big for a 16? Bearcole1 General Unicycling Discussions 11 2013-06-14 05:35 PM
I am looking for someone to do a Unicycle Demo at a Motorcycle Event. TrialsTrainingCenter General Unicycling Discussions 0 2013-04-02 08:07 PM
Looking for a new unicycle; How's this one? DaveGrohl Unicycle Product Reviews 8 2013-03-17 06:07 AM


All times are GMT. The time now is 12:35 AM.


Powered by vBulletin®
Copyright ©2000 - 2015, Jelsoft Enterprises Ltd.
Copyright © 2001-2019 Gilby
Page generated in 0.11795 seconds with 14 queries